Collusalus DOA

[GVC66]

Not having any luck with flangers at all...  Here is a start for the voltage readings.  I did not complete this because something seems VERY off.  Can someone with more mxr flange experience tell if this is fubar and I should scrap it?

IC1:
1.382
.934
361.5mv
1.4mv
14.81
1.37
Varies
.82

IC2:
Decreasing
Decreasing
217mv
1.5mv
235mv
.5mv
.5mv
.5mv

IC3:
.73
0
.787
1.4mv
234.9mv

[dwmorrin]

Don't scrap it yet.  You need to put the pin numbers next to the voltage readings.  The only thing close to +15 I see is "14.81", but it's unclear which pin.  That would be OK for pin 8.

IC2 doesn't have any sign of power.  Should have +15 on pin 8.

IC7 and 8 supply the power to the rest of the board.  Check those.  You need to get +15 on IC8 Vo, and approx. +7.5V for "VB."

[Govmnt_Lacky]

+1 for labeling the pins. Need to post properly labeled voltages for ALL of the ICs before anyone can assist.

Also, post voltages on the regulator 

[GVC66]

My bad.  The pins are ascending order... IE

1
2
3
4
5
Etc...

I should have said something.

[Govmnt_Lacky]

If that is the case then there is definitely something wrong. Should NOT have 14.8V on Pin 5 of IC1

Are you using an LT1054 for IC7? Have you double checked ALL component values and cap orientations?

Can you repost with ALL voltages for ALL ICs and the regulator?

[GVC66]

I just noticed I used bc549b instead of c.  I just ordered some bc549c.  Could that be it?  Should I continue to check voltages or should I wait till I replace the npns?

[Govmnt_Lacky]

I just noticed I used bc549b instead of c.  I just ordered some bc549c.  Could that be it?  Should I continue to check voltages or should I wait till I replace the npns?

I doubt it. You really should repost your source voltage and new reading at the pins of all the ICs. Make sure you properly label them! 

[GVC66]

Ic1--
1=1.371
2=.97
3=358.7 mv
4=1.5 mv
5=.813
6=1.345
7=0
8=14.81

Ic2
1=decreasing
2=decreasing
3=215.2mv
4=1.5mv
5=descending
6=descending
7=.3mv
8=233mv

Ic3
1=.723
2=120.8mv
3=.782
4=1.5mv
5=121.2
6=.717
7=.832
8=233.6mv

Ic4
1=2.218
2=decreasing
3=2.2
4=1.5mv
5=227mv
6=12.22
7=14.14
8=14.8

Ic5
1=14.8
2-7=7.39
8=1.5mv
9-12=7.39
13=decreasing
14=increasing
15=increasing
16=decreasing

Ic6
1+2=7.39
3=14.71
4=1.3mv
5=7.39
6=1.4mv
7=1.3mv
8+9=14.8
10=10.44
11-14=14.8

Ic7
1=9.29
2=1.418
3=2.54
4=180.6mv
5=6.2mv
6=1.9mv
7=4.6
8=1.371

Ic8
1=16.57
2=decreasing
3=14.8

Ic9
1=scattered
2=7.39
3=decreasing
4=1.585
5=decreasing
6=7.39
7+8=10.02

[GVC66]

Is my pinout ok?

[GVC66]

I forgot to mention I am using 9volts as my source (1spot).

[GVC66]

Just went through this again and I am at a loss. All the parts seem to be correctly oriented and soldered cleanly.