- Welcome to madbeanpedals::forum.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
#1
Open Discussion / Re: Mammoth Electronics and powder coated enclosures
November 08, 2019, 12:16:50 AM #2
Open Discussion / Re: Off Topic Mostly: Contractor Rant
August 05, 2014, 12:37:00 AM
Damn! What a headache! Sorry to hear about that. Hopefully when your lawyer now involved it'll get done the way you wanted.
#3
Build Reports / Re: Maestrophetamine - Sharkfin build
June 26, 2014, 03:23:45 AM
Ha! LOVE IT!
Both inside and out!
Both inside and out!
#4
Open Discussion / Re: Oddball phaser on EB
June 14, 2014, 02:19:25 AM
I have one of those. It sounds pretty cool. I believe it is an 8 stage phaser.
#8
Build Reports / Re: Razzle Dazzle
April 22, 2014, 01:11:46 AM
Wow! How do you keep up with the same color wiring? Amazing!
#9
General Questions / Re: Best delay with PT2399
April 15, 2014, 07:15:44 PMQuote from: PhiloB on April 15, 2014, 06:50:27 PM
I have the original Hamlet PCB. I'd be willing to part with it (Want to build the Hamlet+;)
Hey if the OP does not want your Hamlet PCB, I'd be interested in it.
#10
Build Reports / Re: Univibe / Harbinger
April 10, 2014, 01:42:30 AM
Very nice!!! How did you do the lettering? Stickers?
#11
Open Discussion / Re: So, what's going on in the solo here?
March 15, 2014, 11:28:04 PM
That is definitely a Boss T-Wah.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
#13
General Questions / Re: Good Source fof J201 and 2N5457
March 04, 2014, 06:14:40 PM
Hey, where are y'all getting through hole adapters from? I just googled and only found adapters for IC's.
#14
Open Discussion / Re: What type of fuzz circuit would you say this is?
March 04, 2014, 03:14:16 PM
Man that's a great tune!
#15
General Questions / Re: Best Fuzz Face board for experimenting with my russian PNP's
February 28, 2014, 05:57:48 PM
I came across a thread that forum member Gus started over at DIYSB about a different way to bias a Fuzz Face that I am interested in trying.
Gus has suggested biasing the circuit by using a 5K trim pot on the emitter of Q2 instead of changing the 8K2 on Q2 collector.
I will see if I can find the thread and I will link it here because he has a new way to bias the circuit. IIRC you add a 1M in parallel with the 100K feedback resistor.
Also, in the thread member mac posts a schematic of how he biases the circuit that looks interesting.
After you read their ideas and then go back and read RG Keen Technology of.... article it makes sense. Anyway, I'll try to find what I am talking about.
It might be something to try since you have the circuit on the breadboard.
Ok, found it! But, realized it is for biasing Si transistors. Don't see why it work with Ge though.
http://www.diystompboxes.com/smfforum/index.php?topic=104818.0
Gus posted his schematic with the 5K trimmer I was referring to.
Gus has suggested biasing the circuit by using a 5K trim pot on the emitter of Q2 instead of changing the 8K2 on Q2 collector.
I will see if I can find the thread and I will link it here because he has a new way to bias the circuit. IIRC you add a 1M in parallel with the 100K feedback resistor.
Also, in the thread member mac posts a schematic of how he biases the circuit that looks interesting.
After you read their ideas and then go back and read RG Keen Technology of.... article it makes sense. Anyway, I'll try to find what I am talking about.
It might be something to try since you have the circuit on the breadboard.
Ok, found it! But, realized it is for biasing Si transistors. Don't see why it work with Ge though.
http://www.diystompboxes.com/smfforum/index.php?topic=104818.0
Gus posted his schematic with the 5K trimmer I was referring to.