Messages

Same guy, different forums 🤣
But thanks to everyone who helped out.
Don't know why it would have had an issue. I did use a gigrig electroman power supply to start with but then on advice got a proper EHX one.

Thanks for reaching out. I literally just solved it with some help from some fine fellows!

I think it turned out to be a faulty voltage reg. I changed the, R57 and also the trim pot for Bias 2 and its working like a dream now.

Thanks to all those involved.

Morning Brian

So I did what you suggested and checked all the resistors, from R9-R15 and all are good. I managed to check R15 and R14 in place and read 33K and 16K respectively

I wasn't getting correct readings from R9-R13 as im assuming, being in the circuit makes some difference to these. So I used a new one of each value and measured it correctly and then checked the code against the resistors and got 68K 24K and 51K for each of those.

I doubt replacing them would make a difference, but can do that if you think it would help.

The Values of all the resistors in the delay line and they are all fine too.

The "Squeel" is actually on pin 2 of IC3. Pin 1 and Pin 3 are fine. Adjusting the feedback makes no difference to the squeal. The audio on pin 3 is quieter than pin 3 but im guessing thats ok. I changed the JRC4558 out for several different ones and still the same.

I have audio on pin 3 and 4 of IC6 and also on pin 5 and 6 of IC 4. I still have absolutely no voltages on pin 5 to pin 8 on IC4!

I have NO audio at all on pin 3 or 4 of IC7.

I have swapped the MN3005 around and get the same issues.

I have continuity between IC4 pin 7 and IC7 pin 7 and R46 and Gain 1 etc. And from IC4 pin 4 and bias 2.

I have swapped out IC4 to several different JRC4558 and still the same issues.

Any thoughts from here about what else I could do? Got me totally stumped.

Thanks in advance.

Thanks Brian. I will go check those resistors again. Always helps to double and triple check. Will get back to you once I have checked those.

I don't know why but the issue with IC4 makes me feel something strange is going on there. I will keep investigating but am running out of ideas!

Watch this space....

Please see the attached pics for more details..

Morning all.

It pains me to post this here as I took my time on this one as I knew it's a complex built. I was hoping to beat @MichaelW to a build report but we both hit problems at the same time. He got a new board and got it working. I'm persevering with mine thought as I want to know what I have done or not done!

So before I loose my patience and or my mind and start ripping things off the board I thought I would ask around on here. I know there are some very accomplished builders and some total recall experts here!

Firstly I have checked values. Cleaned the board. And started an audio probe.

Going from the main audio schematic it's all good. I get a squeal on pin 3 of IC3 not sure if that's an issue.

Audio stopped at C14 so I replaced that and it's fine now. All the way to D in. After that nothing.

I her audio on pin 3 and 4 of IC6 but no delay at all.

Looking at my voltages everything looks good apart from IC4. I get nothing at all ok the right hand side.

I also get no voltage at pin 7 of IC7. Could this be related to the issue at IC4?

My thoughts is a bridge or issue in the socket for IC4. Before I take it off does this sound like it might be the issue?

Any thoughts and suggestions very very very welcome!

I cant seem to attach pictures. Please tel me how!!

Phil

Wow that is truly stunning. I followed you first build almost word for word whe. I built mine. This one makes me feel like I want to do it again, but like you even better.
Thanks for keeping me pushing myself to learn and work harder and better and strive for the best.

I have been travelling for the past two years with circuit boards and passive components like resistors and caps and diodes etc.
I used to have to isolate for 5 days prior to joining my work site so I used to travel with a small sanity helper which included pedal kits and some basic tools like soldering iron etc.
I used to populate all the basic and time consuming bits before taking them home to finish them.
They were all in checked luggage and not hand luggage but I was never asked once what they were. I used the Tayda bubble wrap and anti static bags too just in case.
So far the only issues I have found have been from my building, not from flying with them 🤣

I have actually just re-looked at his page for this project and the art work is there already. So can use that to do it. Perfect!

That's a good idea. I will drop him a line. It makes it look very professional indeed.

Looks amazing. Where did you get the enclosure from??

Got it! Cheers.

Phil

Love your build! I have just finished my enclosure for the same pedal. Board is 75% populated. So I'm getting close. Just got to put the final bits in before I test it.
Where did you get the generator and scope from? They look ideal for this kid of stuff. With our taking up too much space or breaking the bank!
Thanks in advance

Phil