News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - karter2000

Pages1 2 3 4
#1
Global Annoucements / Re: 2024 outlook
April 29, 2024, 04:50:15 PM
Sorry if I missed this somewhere, but are the Trash Compactor and Mysterioso coming back?
#2
Open Discussion / Re: VFE SPS code + more (askin fer help)
August 05, 2023, 08:49:38 PM
I got some 12F509 through my work, and they appear to be programming properly with my Pickit2 clone.  I'm going to breadboard the circuit just to make sure.
#3
Build Reports / Re: Smooshy face - and Afterlife on +-9V and a clean blend/boost
November 27, 2022, 09:28:37 AM
Dou you have a layout available?  I have an afterlife that I love, but would love to build this.
#4
General Questions / Basic PT2399 Delay PCB
October 20, 2022, 08:23:26 PM
Hi all,

I got a few PT2399's years ago, but never really used them.  I'm looking for a PCB for a basic PT2399 delay, so that I can try them out, as well as experiment with the various mods available (modulation, tape stop effect posted in this forum, tap tempo, etc).

Thanks!
#5
Tech Help - Projects Page / Re: DigDug2 VTL5C9
June 09, 2022, 03:42:32 AM
Quote from: oeslicoalfin on June 09, 2022, 01:24:28 AM
I've had good luck with Thonk UK: https://www.thonk.co.uk/shop/vactrols-vtl5c/
They always have a broad selection of Xvive vactrols.
The downside is the exchange rate of #sterling to USD, but I've never had any problems with being shipped a bad photocoupler.

Thanks!  I didn't even think to check Thonk.  At this point, I'd buy from just about anywhere  ;D.
#6
Tech Help - Projects Page / DigDug2 VTL5C9
June 08, 2022, 10:47:09 PM
Hi all,

I have a DigDug 2 PCB which I'm finally going to get around to populating.  With (trustworthy) VTL5C9's pretty much non-existent, what are my options as far as a sub for the VTL5C9?

Thanks!
#7
Open Discussion / Rate for Fixing Pedals
September 21, 2017, 07:32:55 PM
Hi all,

I get asked all the time to fix pedals, but I never have any idea on what to charge.  For those who fix as well, do you have a specific rate?

Thanks!
#8
Open Discussion / Re: diyguitarpedals update (closing down)
August 02, 2017, 04:10:03 AM
All the best to you Paul, and your family.
#9
Build Reports / Re: Gristle King, BB and AT drive
April 15, 2017, 04:43:17 PM
Awesome job, and I love the design of the PCBs.  What are circuits based on?
#10
Build Reports / Re: Wolfbox Direct Box
April 14, 2017, 05:19:27 AM
Looks awesome!  How much did the transformer set you back?
#11
VFE Projects / Re: VFE Projects FAQ
April 09, 2017, 08:18:18 AM
Any projected date for the Triumvirate?  I'm extremely interested in that one!
#12
Open Discussion / Re: Melvins Fans! DIY Sunn Beta Lead / Bass Pre-amp Stompbox
February 07, 2017, 04:57:56 AM
I voted for the Beta Bass Preamp, as I'd love one of those to build.
#13
Open Discussion / Re: A good blend pcb? For bass?
December 27, 2016, 08:11:59 AM
I have an extra GuitarPCB Paramix if you are interested.
#14
Introductions / Re: Greetings again from Vancouver, BC
March 18, 2016, 04:00:19 AM
I'm a Lower-Mainlander as well (Burnaby)!
#15
General Questions / Re: Good preamp for bass
May 08, 2015, 12:29:55 AM
Quote from: HamSandwich on May 07, 2015, 05:27:38 PM
http://sound.westhost.com/project152-1.htm

A pretty extensive bass preamp. I'm about to get boards fab'd that include the input, tone controls, HPF, comp and drive sections as well as balanced outputs and a power board. Not sure how long you want to wait, but I'll have a few extra that I'm going to try to get rid of.

I would be interested in those boards!
Pages1 2 3 4