Show posts

#1

Build Reports / Re: Imp/Cave Dweller (Lead Loop Thingy)

November 11, 2020, 03:44:14 AM

I love this! Did a similar thing with a Rangemaster and a Cave Dweller...no loop on mine. That said, not having to tap dance for that instant lead boost + sweet echo tone = priceless.

Sent from my SM-G960U using Tapatalk

#2

Open Discussion / Multiplex Single Repeat or Oscillation

October 22, 2019, 05:19:32 PM

Hello,

Finished wiring up my Multiplex with Mod board and found that I get only one echo repeat across the entire sweep of the repeat knob until it goes instantly into full modulation at the very end of the range.

I do get a different delay sound between each mode (delay 1 and 2 on RE201 and Binson mode, just the one delay on Echoplex), pretty sure I'm getting the full delay time sweep on both delay knobs, mix control works, and the modulation works fine.

IC1
4.12
4.13
4.11
0
4.10
4.13
4.12
8.26

IC2
5.09
2.54
0
0
3.04
2.54
.19
.68
2.54
2.54
2.54
2.54
2.54
2.54
2.55
2.55

IC3
5.09
2.54
0
0
2.94
2.54
.23
.70
2.55
2.55
2.55
2.55
2.55
2.54
2.54
2.55

Tried running through all the solder points but nothing is sticking out to my untrained eye. Is there a specific are on the board where I need to be concentrating my efforts?

Sent from my SM-G960U using Tapatalk

#3

Open Discussion / Multiplex Single Repeat or Oscillation

October 22, 2019, 05:18:24 PM

Hello,

Finished wiring up my Multiplex with Mod board and found that I get only one echo repeat across the entire sweep of the repeat knob until it goes instantly into full modulation at the very end of the range.

I do get a different delay sound between each mode (delay 1 and 2 on RE201 and Binson mode, just the one delay on Echoplex), pretty sure I'm getting the full delay time sweep on both delay knobs, mix control works, and the modulation works fine.

IC1
4.12
4.13
4.11
0
4.10
4.13
4.12
8.26

IC2
5.09
2.54
0
0
3.04
2.54
.19
.68
2.54
2.54
2.54
2.54
2.54
2.54
2.55
2.55

IC3
5.09
2.54
0
0
2.94
2.54
.23
.70
2.55
2.55
2.55
2.55
2.55
2.54
2.54
2.55

Tried running through all the solder points but nothing is sticking out to my untrained eye. Is there a specific are on the board where I need to be concentrating my efforts?

Sent from my SM-G960U using Tapatalk

#4

Open Discussion / Multiplex Single Repeat or Oscillation

October 22, 2019, 05:16:51 PM

Hello,

Finished wiring up my Multiplex with Mod board and found that I get only one echo repeat across the entire sweep of the repeat knob until it goes instantly into full modulation at the very end of the range.

I do get a different delay sound between each mode (delay 1 and 2 on RE201 and Binson mode, just the one delay on Echoplex), pretty sure I'm getting the full delay time sweep on both delay knobs, mix control works, and the modulation works fine.

IC1
4.12
4.13
4.11
0
4.10
4.13
4.12
8.26

IC2
5.09
2.54
0
0
3.04
2.54
.19
.68
2.54
2.54
2.54
2.54
2.54
2.54
2.55
2.55

IC3
5.09
2.54
0
0
2.94
2.54
.23
.70
2.55
2.55
2.55
2.55
2.55
2.54
2.54
2.55

Tried running through all the solder points but nothing is sticking out to my untrained eye. Is there a specific are on the board where I need to be concentrating my efforts?

Having an issue getting pics to post, will figure out and get them posted ASAP...

Thank you

Sent from my SM-G960U using Tapatalk

#5

Open Discussion / Multiplex Single Repeat or Oscillation

October 22, 2019, 01:17:22 PM

Hello,

Finished wiring up my Multiplex with Mod board and found that I get only one echo repeat across the entire sweep of the repeat knob until it goes instantly into full modulation at the very end of the range.

I do get a different delay sound between each mode (delay 1 and 2 on RE201 and Binson mode, just the one delay on Echoplex), pretty sure I'm getting the full delay time sweep on both delay knobs, mix control works, and the modulation works fine.

IC1
4.12
4.13
4.11
0
4.10
4.13
4.12
8.26

IC2
5.09
2.54
0
0
3.04
2.54
.19
.68
2.54
2.54
2.54
2.54
2.54
2.54
2.55
2.55

IC3
5.09
2.54
0
0
2.94
2.54
.23
.70
2.55
2.55
2.55
2.55
2.55
2.54
2.54
2.55

Tried running through all the solder points but nothing is sticking out to my untrained eye. Is there a specific are on the board where I need to be concentrating my efforts?

Having an issue getting pics to post, will figure out and get them posted ASAP...

Thank you

Sent from my SM-G960U using Tapatalk

#6

Open Discussion / Multiplex Single Repeat or Oscillation

October 22, 2019, 01:16:28 PM

Hello,

Finished wiring up my Multiplex with Mod board and found that I get only one echo repeat across the entire sweep of the repeat knob until it goes instantly into full modulation at the very end of the range.

I do get a different delay sound between each mode (delay 1 and 2 on RE201 and Binson mode, just the one delay on Echoplex), pretty sure I'm getting the full delay time sweep on both delay knobs, mix control works, and the modulation works fine.

IC1
4.12
4.13
4.11
0
4.10
4.13
4.12
8.26

IC2
5.09
2.54
0
0
3.04
2.54
.19
.68
2.54
2.54
2.54
2.54
2.54
2.54
2.55
2.55

IC3
5.09
2.54
0
0
2.94
2.54
.23
.70
2.55
2.55
2.55
2.55
2.55
2.54
2.54
2.55

Tried running through all the solder points but nothing is sticking out to my untrained eye. Is there a specific are on the board where I need to be concentrating my efforts?

Thank you,
Curtis

Sent from my SM-G960U using Tapatalk

#7

Open Discussion / Multiplex Single Repeat or Oscillation

October 22, 2019, 01:16:14 PM

Hello,

Finished wiring up my Multiplex with Mod board and found that I get only one echo repeat across the entire sweep of the repeat knob until it goes instantly into full modulation at the very end of the range.

I do get a different delay sound between each mode (delay 1 and 2 on RE201 and Binson mode, just the one delay on Echoplex), pretty sure I'm getting the full delay time sweep on both delay knobs, mix control works, and the modulation works fine.

IC1
4.12
4.13
4.11
0
4.10
4.13
4.12
8.26

IC2
5.09
2.54
0
0
3.04
2.54
.19
.68
2.54
2.54
2.54
2.54
2.54
2.54
2.55
2.55

IC3
5.09
2.54
0
0
2.94
2.54
.23
.70
2.55
2.55
2.55
2.55
2.55
2.54
2.54
2.55

Tried running through all the solder points but nothing is sticking out to my untrained eye. Is there a specific are on the board where I need to be concentrating my efforts?

Thank you,
Curtis

Sent from my SM-G960U using Tapatalk

#8

Open Discussion / Multiplex Single Repeat or Oscillation

October 22, 2019, 01:16:07 PM

Hello,

Finished wiring up my Multiplex with Mod board and found that I get only one echo repeat across the entire sweep of the repeat knob until it goes instantly into full modulation at the very end of the range.

I do get a different delay sound between each mode (delay 1 and 2 on RE201 and Binson mode, just the one delay on Echoplex), pretty sure I'm getting the full delay time sweep on both delay knobs, mix control works, and the modulation works fine.

IC1
4.12
4.13
4.11
0
4.10
4.13
4.12
8.26

IC2
5.09
2.54
0
0
3.04
2.54
.19
.68
2.54
2.54
2.54
2.54
2.54
2.54
2.55
2.55

IC3
5.09
2.54
0
0
2.94
2.54
.23
.70
2.55
2.55
2.55
2.55
2.55
2.54
2.54
2.55

Tried running through all the solder points but nothing is sticking out to my untrained eye. Is there a specific are on the board where I need to be concentrating my efforts?

Thank you,
Curtis