News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - dromilious

#1
hello guys ! I made two pieces of the mudbunny the green russian edition.I used the 5088 transistors.The only difference is that i used 330 ohm resistors in place of the 390 ohm.My sound is more a distortion with a bit fuzz.i compared it with mudbunnies at youtube and i can hear more fuzz at them.My hfe of the trans is about 350.I used my probe and i checked that the first boost stage gives me the same signal as the input.no boost at all.Any ideas ?
#2
Build Reports / Re: wolfshirt - with ultimate octave mod
December 04, 2012, 08:46:37 PM
Hello.Can you please make a diagram with the bright switch?thank you!
#3
Mods / Re: Loophole , IC-change? ISD25xx 40sec Mod?
July 13, 2012, 12:48:24 PM
claytushaywood did it work your loophole with the isd2560?I have one spare and i think to make a try.So the only think you have to do is to jumper 7 and 8 pins to ground?
#4
Tech Help - Projects Page / Re: Uproar Gain problem
March 29, 2012, 08:25:53 PM
Hello.Actually i don't have a gain problem but i need more gain from this.How i could do this ?changing the gain pot maybe ?Also i need more brightness from the tone maybe more mid range.for this i will change c8 and c9 .But with the gain ?
#5
Tech Help - Projects Page / Re: Krankosaurus...
January 27, 2012, 04:37:05 PM
Thank you boys.That's exactly what happens to my pedals.Like the video Loztboy posted.crackle!So it works fine :) but i want to get rid of crackle at my Booster.
Thank you so much !
#6
Tech Help - Projects Page / Re: Krankosaurus...
January 26, 2012, 09:42:49 PM
My krankosaurus has a problem.my Boost and gain pots make an anoying hissss when i turn them on especially after the last half rotation.The same thing happens and at one booster i made using the boost section of the krankosaurus.I have to say that i use 2n7000 and log pots and not anti log.
What really happens?
#7
Open Discussion / Re: max1044a
January 19, 2012, 03:53:40 PM
thanks for your answer.i ordered 10 pieces for 5 dollars :)
#8
Open Discussion / Re: max1044a
January 19, 2012, 03:35:46 PM
I have found the ICL7660S.can i use it for max1044?
#9
General Questions / Re: power supply Hum problem
January 08, 2012, 10:15:40 AM
thank you very much for your advise.I will check them!
#10
General Questions / Re: power supply Hum problem
January 07, 2012, 10:37:50 PM
I used this adaptor http://www.visualsound.net/index.php/products/pedal_power_supplies/1_spot_power_supply.It is a Jack Oman's Mosfet based booster.I used it with a MXR chorus powered both with the 1 pot adaptor.I tried also with an other adaptor alone.
#11
General Questions / power supply Hum problem
January 07, 2012, 05:02:21 PM
Hello all.I have a problem with my power supply.It is a one spot supply.When i connect it to the pedal(booster) it makes a hum.When i plug a battery i have not any noise.How can i solve this prolblem?
thanks
#12
Open Discussion / Re: *POP* goes the pedal
January 06, 2012, 10:56:42 PM
Hello.I have Pop problems with most of my boost pedals and some distortion.When i plug dc in the circuit and turn on for the first time the 3pdt then it makes this pop sound.When i turn it to bypass and back to circuit signal the pop desapears.So it happens only the first time it takes dc.
P.S. i dont ground the input circuit at the bypass mode.Also i use 33 k resistors for my high brightness leds .