Messages

Ugh!  So I've been over the wiring several times, and I just don't find anything wrong.  I tried grounding the jack to the enclosure and that didn't help the hum.  Does anyone have a suggestion for systematically debugging the hum, maybe in particular that everything is grounded correctly?

The olcircuits.com people suggested moving the power rectifier/filter pcb away from the signal wires which means redoing all the wiring to that pcb with longer wires and moving it to the other end of the enclosure.  I would rather do a bunch of testing to rule other things out first before I do a bunch of desoldering and rewiring.

second suggestion, is the enclosure grounded?

you have insulated jacks so that could be the problem. use a multimeter to check continuity between ground and the case.

if theres no continuity a simple solution is to remove one of the jacks, file a SMALL groove in the hole in the enclosure and use the jack to hold a ground wire in the groove.

Sent from my SC-02B using Tapatalk 2

if you don't have a file, you can also ground to the back of a pot. you'll need to heat it up for a while with the iron, but it should be able to hold solder.

I'm not sure what you mean when you say that the jacks are disconnecting ground when the plug is inserted,  can you please explain what that means.

So the second suggestions in practical terms is to ground the sleeve of the jacks to the case or the pot?  Thanks, I will check continuity to the case.

Hey Jacob, thanks for your input.  there is a black wire (very hard to see in this picture) going from the tip of the output jack, under the pcb to lug 8 of the 3PDT switch.  I imagine if I had nothing hooked to the tip of the output jack the signal wouldn't be working.  Everything works great with this pedal, I'm just getting a hum.  the hum comes in when I switch the pedal on, stays the same no matter how I set the knobs, and goes away when I go to bypass.

One of your jacks, the upper one, is not connected properly. It looks like you have connected nothing to the tip of that jack, and are only connected to the sleeve. Connect the sleeve to ground on both jacks, and use the tip of each jack to connect to the switch. The tip is farthest from the enclosure hole, and the sleeve is closest to the enclosure hole.

Jacob

gordo, thanks, I did spend a lot of time doing this.  The output jack goes under the pcb to (what I understand to be) lug 8 of the 3PDT.

Hey everybody thanks for all the suggestions.  connecting the LED to ground solved the LED problem!     but the hum persists 

Here is a pic of the wall wart:



here's a picture of the build (sort of shy about this, being my first one and all - don't laugh )



maybe this can give some insight into what I can do to decrease the hum.

I got this reply from another forum:

There's one huge omission in the build doc - they don't ground the stomp switch.  That's probably why your LED doesn't light up.  Connect either the top middle or bottom left lug (when looking at the diagram - they are connected to each other so it doesn't matter which one you use) to ground - the sleeve of the input jack is probably the easiest place.

does this sound right with anyone/everyone here?  You can see the build doc in the initial post above.

I'll have to check on the mA rating when I get home tonight.

I have contacted OLC as well, I just thought it would be cool to start getting into these forums so that I can learn from a whole bunch of people.  thanks! I will check out that voodoo labs power supply.

Hi, First time posting, first build.  I put together the "officially licensed circuits" "Darth Fader" tube tremolo pedal recently.  I was shocked when I hooked it up and it mostly worked in terms of the signal and the effect.  There are two problems, and I'm not sure how to go about debugging them.  Firstly, the LED is not lighting up. Second, there is a substantial hum that kicks in when I turn the effect on.  Any suggestions on debugging these problems would be greatly appreciated.  I'm at work so I don't have pics of my particular build right now, but here is a link to the pdf of the instructions for the pedal:

http://www.olcircuits.com/documents2008/olc_darthfader_buildguide.pdf

In terms of the LED, I'm sure I got the polarity right.  The way they say to hook up the LED to the 3PDT looks different than I have seen in other pedals.  Usually the negative lead of the LED goes to terminal 4 of the 3PDT and in this design they have it go to 2.  Could just be a bad connection somewhere, but I was pretty careful.

As for the hum, could just be the wall wart, and I don't currently have another one to try, but I suppose I should get another.  Any other ideas about the hum would be appreciated.