News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - copachino

#1
i had the same problem but, i got use this method, dial the gain until the led stop flashing(the led that its up the pcb) when it stop flashing set the other knobs like volumen and sweep until you like it, tou have to do that always you move a switch.

tht how it works for me
#2
Open Discussion / timefactor aux pedal
April 24, 2016, 07:57:25 PM
hi, all i have a time factor delay and a dd7 delay, the thing its i want to control tap tempo with just one switch and the preset with another one, but i want the tap tempo for both pedals to be the same, i have two carling SPSt NO switches, but im no so sure about the wiring, do i connect one switch lugs to tip and ground, so when i push the switch the delay take ground reference to change the tap??, and i put a diode on the second switch for another reference for the delays to know i want to change banks or pressets??, im a bit confused in here, also for the delays wil be the same wiring but different output ans same switches, so the output jacks will be only connected one to each other.
#3
Quote from: BrianS on March 13, 2016, 02:17:43 AM
Do a google search for hardwood (I don't believe you will find the bar the guys are talking about) in Atlanta.  It will bring up several places that will interest you. What you are looking for is businesses that supply cabinet making wood. They will or should have 8/4 (2") or 6/4 (1 1/2") lumber in the variety you are looking for.

hahaha i dont think i could find those bars, mmmm i might have to google some wood places in atlanta
#4
Open Discussion / where to get good wood on atlanta
March 11, 2016, 02:21:23 PM
im traveling to atlanta on april, and i will search for wood, but its somebosy lives or knows where i can get some nice good i would be really happy, id like to get mainly maple, flamed, spalted or any nice looking maple, maybe some alder and some ash, im really into guitar building right konw, but i can only get Honduran mahagony, and some other nice woods, but maple alder and ash its something i cant get anywhere in my country.
#5
thats awsome, me wants, did you made the pcbs??
#6
can you post the link of the red one??, i really dig that one
#7
its that powdercoat??, it really looks nice
#8
Open Discussion / wampler pinnacle deluxe help
March 02, 2016, 01:04:50 AM
i got a friend who got a pinnacle that got burned a resistor that ints on the output of 9v i think its labeled R30 but im not so sure its the one that goes to the drain of Q4, does anybody have a pinnacle deluxe that could help me to replace that one??, somebody was clever enough to connect a 12v on that pedal, and the resistor could not resist that.



#9
Quote from: madbean on February 21, 2016, 05:23:57 PM
Quote from: alparent on February 21, 2016, 04:16:39 AM
One way Brian could help is to widen the space between the traces and the plane.

I hear you, but it is unlikely. The isolation pour is 28mils on all the EP stuff and it would be difficult to get it much wider than that without having to make some compromises on PCB size. But, the nice thing about single sided designs is that it very easy to hit a spot with some solder wick if it looks sketchy.


Brian, could it be possible to get the soldermask layer??, im tying to give away my soldermask since i got like too much and it was supposed to be used by 10-2015, so im trying today if the mask its still good, but if its good, the soldermask layer will be so helpful
#10
Open Discussion / Re: More SMD goodness (hopefully!)
February 20, 2016, 03:31:53 PM
i would be very very interested on buying some of that small stuff
#11
Quote from: alparent on February 19, 2016, 04:22:23 PM
Is shipping to Canada more then 2$  ;D

i guess its about  10 USD not big deal, but im no so sure how long it would take, pm your address please to get it on the way tomorrow
#12
Quote from: alparent on February 19, 2016, 02:45:43 PM
Sure looks interesting.

i will cut some of the mask tonight and check out the shipping to canada tomorrow
#13
Quote from: alparent on February 19, 2016, 01:04:02 PM
Quote from: copachino on February 19, 2016, 04:07:59 AM
i got like a huge box with dupont soldermask, its quite amazing and easy to use, i you want to try i can send you some but im not so sure how long it can take since i live outside usa

From Honduras to Canada, postage might be pretty high?
But would like more info on it. You have a picture, a link or something?

since its just an envelope i dont think its too high but i will check out, its quite good but i dont use it anymore, i had a tutorial over here let check it out


EDIT:
here its the tutorial
http://www.madbeanpedals.com/forum/index.php?topic=15392.msg144910#msg144910
#14
i got like a huge box with dupont soldermask, its quite amazing and easy to use, i you want to try i can send you some but im not so sure how long it can take since i live outside usa
#15
Build Reports / Re: Cab-Sim/Headphone-Amp/Blender
February 08, 2016, 02:57:41 PM
do you still have some pcbs??