News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - daverik

#1
General Questions / PNP Mangler positive bias voltage?
September 14, 2013, 08:05:57 PM
So, I've got this Mangler together and when I set the bias using the test points on the board I get +4.5 v with the black lead from the DMM on the test pad and the red lead to ground.  Unless I am misunderstanding the process, (which is entirely possible), this should be negative 4.5 v, correct?  I am using the "Fuzz Face PNP, US" transistors from smallbear, and used their supplied resistors (with the exception of R-3 which I kept according the the Madbean schematic along with the 20k bias trimmer).  I'll take some voltage readings later today on the transistors and post them here, along with some photos.  I've checked the battery leads and they are correctly hooked-up (+ to ground, - to 9v-), hit all the solder joints again and checked the polarity of my caps, all OK.  Any thoughts before I upload some photos?  Thanks, Dave
#2
General Questions / Re: Add tone stack to Mangler?
September 13, 2013, 02:34:42 PM
Thanks for the info.  I think I'll just build it "stock" for now.  I can always play with it after I get it done.  I have one of Jack Orman's tone stack built as a stand alone effect.  Maybe I'll just put it inline after the Mangler and see how it goes.  Again, thanks.  Dave
#3
General Questions / Add tone stack to Mangler?
September 11, 2013, 02:37:47 PM
Greetings all,  I want to add a "Big Muff" style 2 pot tone control circuit to my Mangler build.  Would I just connect the "out" line from the Mangler board to the "in" side of the tone circuit and then continue out of the tone circuit to the amp? Dave.
#4
Well, I took the .22 electrolytic out and put a film cap in, no change (actually, two .1 film caps wired in parallel).  I guess .22 electrolytic caps are not the norm,  usually this low they go to film, correct?  I have a ton of yellow .22 electrolytic caps from an old Thomas organ that I've been recycling. 

Since I made this change I have been away from the bench for a few days and have not had a chance to do any further testing.  I will take some photos and post them once I get back.  Thanks for all the assistance.  I've modded several pedals but this is my first "ground-up" build.  The way I look at it, I'm gaining valuable diagnostic skills.  Dave.
#5
Wow... I really need coffee before I post.  This is a Cherrybomb, not a Mangler (that's what's on the bench now).  Thanks for the quick reply.
#6
Greetings all,

Just completed my Cherrybomb build and am having  a strange problem.  When I power the pedal on all is fine and it sounds great, for about 5 - 10 seconds.  Then it goes into the fuzzy / fizzy / distorted mode I think I've read about on these boards.  I've changed transistors, no difference.  Here are some specifics on the pedal, maybe someone can point me in a direction.  I've already re-flowed all the solder joints (3) times so I don't think it's that.

Input voltage at battery - 8.8v (tried another battery at 9.6v, no change).
I used an electrolytic cap for C-1 with the minus side to output (tried the other way, no change).
I used a 4-position switch for the gain control with 33k, 50k, 81k and 1k resistors on the outputs (tried removing this and using a 5k trimpot, no change).
Transistors - Q1 and Q2 - 2n2222, Q3 - 2n3904 (tried Q1 and Q3 - 2n3904, Q2 - 2n2222, no change).

Voltage at the transistors are:

Q1

C - 1.38
B - .30
E - .06

Q2

C - .80
B - 1.37
E - .73

Q3

C - 5.42
B - 1.5
E - .88

From scanning these boards it seems the only one in range is Q3.  Any ideas on where to look first (or second, or third...).  Thanks, Dave.